This is the damper-side cover for the black Model D Indoor Rower. Does not include the four damper fan cover screws (order separately, part number 1276). See more info.
For use with Model D and E Indoor Rowers. This is the generator base and coil that transmit flywheel motion to and generates power for the Performance Monitor on your indoor rower. See more info.
This is the handle drive cord for a Dynamic Indoor Rower. The handle drive cord is a single cord that is connected to the handle on one end and the foot carriage on the other end. Not for use on Model A, B, C, D, or E. See more info.
For use on all Model C, D and E Indoor Rowers. This is the stainless steel track for all rowers manufactured after January 1994. It measures 48 inches long and includes double-sided tape and two rivets for installation. See more info.
For use on the Model D and E Indoor Rower.
For use on all Model D, E, Dynamic Indoor Rowers, SkiErg1s and SkiErg2s. This is the metal perforated part of the flywheel cage that wraps around the circumference of the flywheel. This part includes the connectors, screw and nut. See more info.
For use with Model D and E Indoor Rowers and the SkiErg. This is the sensor coil for the power generator that transmits flywheel motion to and generates power for the Performance Monitor on your indoor rower or SkiErg. See more info.
Let’s face it: the backside works hard during rowing. If you prefer a bit more padding, try our seat pad. Made from 12mm textured rubber, this provides the comfiest row around with cut out sections in the middle for the pelvis and at the rear to accommodate the coccyx. The seat pad can be easily transferred between machines.
For use on the Model D and E Indoor Rower. This is the 14 tooth sprocket for the flywheel axle. If you need to replace the sprocket, you should replace the chain at the same time (see part number 1916). See more info.
If you already own a Polar™ or Polar compatible heart rate chest belt transmitter and would like to enable the PM2/PM2+/PM3/PM4 heart rate monitoring function on your Concept2 Model A, B, C, D, or E Indoor Rower, this Concept2 Heart Rate Receiver is what you need.
For use with Model B and C Indoor Rowers. This kit allows you to retrofit the handle that comes standard on the Model D, E and Dynamic Indoor Rowers to your Model B or C. See more info.
For use with Model A and C Indoor Rowers. This is the pickup (sensor) and cable (wire) that transmit flywheel to the Performance Monitor on your indoor rower. If your monitor lights up with zeros but the display does not change when you begin rowing, you may need to replace this part. If the cable or cable housing is cut or broken you will definitely need...
Replacement handle for the Model D, E and Dynamic Indoor Rowers. Overmolded grips made of soft rubber won´t absorb sweat, grease or dirt. Does not include U-bolt nuts. See more info.
For use on all black Model D Indoor Rowers manufactured after July 2006. See more info.
For use on all gray Model D Indoor Rowers manufactured after July 2012 and all SkiErg1s manufactured June 2009–July 2014. See more info.
For use on all light blue Model D Indoor Rowers manufactured from July 2003–July 2012. See more info.
For use with Model C, D, E and Dynamic Indoor Rowers. One of the 3-1/4 inch wide top seat rollers (two per machine; sold individually) that runs on the stainless steel track on the monorail. Mounting hardware that holds the roller on the seat frame is not included, because it can usually be re-used. If you need the hardware, order part number 1728...
For use on all Concept2 Indoor Rowers. Replacement seat top. 12" wide, 10" deep, 1½" thick, with contours for pelvic bones and tailbone. Mounting screws and lock washers (four each) included. Original equipment on Model C, D, E and Dynamic Indoor Rowers. Can be retrofitted on all Model B and most Model A Indoor Rowers, replacing the original "kidney"...
For use with Model C, D and E Indoor Rowers. This is the 12´ 6" long elastic shock cord (or bungee cord) that recoils the chain on recovery. If your chain recoils slowly—or not at all—between strokes, then you should inspect your existing shock cord. See more info.
The Android Connection Kit is used to connect a PM3 or PM4 to an Android device for using software such as ErgData. NOT COMPATIBLE WITH PM5 DISPLAY!
For use with Model C Indoor Rowers. This is the lever and damper (shutter) on the side of the flywheel housing that slides up and down to change the airflow through the flywheel. Less air through the flywheel (setting = 1) means less drag when rowing; more air through the flywheel (setting = 10) means more drag. Fits Model C Indoor Rowers only. See more...
Replacement case front for the PM2 monitor.
For use with Model C and original Model D Indoor Rowers. This is the Framelock Kit for all Model C and original Model D Indoor Rowers. It includes the axle, the framelock, the framelock cord, two screws, two washers and a hexkey tool.
The new cradle for PM3, PM4 and PM5 monitors.