skip to main content
Model D, Original

Parts listed here are compatible with Model Ds manufactured from July 14, 2003 to July 21, 2006 (serial numbers 071403 to 072106

Model D, Original There are 70 products.

per page
Showing 26 - 50 of 70 items
  • CHF 6,00

    This is the part of the indoor rower that connects to the Performance Monitor on one end and the chain guide brackets on the other. For use on all Model C and Model D Indoor Rowers. See more info.

    CHF 6,00
  • CHF 5,50

    For use with the Model C, D and E Indoor Rowers. This is the 2" x 2" x 3/4" metal traveling pulley assembly with a chain idler pulley included. The chain and shock cord come together at the traveling pulley, and the traveling pulley moves back and forth inside the indoor rower on every stroke. One per machine. See more info.

    CHF 5,50
  • CHF 4,59

    For use with Model C, original Model D and Retrofitted Model A and B Indoor Rowers. This is the 12" molded plastic part anchored with 4 screws and nuts to the metal footplates on the indoor rower, enabling you to adjust the Flexfoot (part number 1063, sold separately) to accommodate different foot sizes and body types. There are two per machine. See more...

    CHF 4,59
  • CHF 4,40

    T27 6-Lobe driver required to turn the front leg fasteners (part number 2952) on Model C, D (original and updated) and E Indoor Rowers.

    CHF 4,40
  • CHF 3,81

    For use on all Model C, D and E Indoor Rowers. This cover fits the underside of the main box frame to protect the return mechanism from dust and to keep little fingers and pets' tails safe from the moving parts inside. See more info.

    CHF 3,81
  • CHF 3,81

    For use with Model C, D, E and Dynamic Indoor Rowers. This is one of the small bottom seat rollers (two per machine; sold individually) that runs under the top edge of the monorail. Does not include the mounting hardware (nut, bolt and spacers) that hold the roller on the seat frame, because it can usually be reused. If you need the hardware, order part...

    CHF 3,81
  • CHF 3,60

    For use on the Model C, D and E Indoor Rower. This is the part that the chain passes through before entering into the flywheel assembly. See more info.

    CHF 3,60
  • CHF 3,31

    For use with Model A, B, C and original D Indoor Rowers. Replacement nylon footstrap with buckle, approximately 24" long by 1" wide with a screwhole drilled approximately 7" from the buckle end. Two per machine. Sold individually.

    CHF 3,31
  • CHF 3,31

    For use with updated Model D, Model E and Dynamic Indoor Rowers.  Replacement nylon footstrap with buckle, approximately 30" long by 1" wide with a screwhole drilled approximately 9" from the buckle end. Two per machine. Sold individually. Model D/E Flexfoot Assembly Diagram

    CHF 3,31
  • CHF 3,10

    For use with Model C, D and E Indoor Rowers. This is a 3-3/8 inch diameter pulley that the shock cord (part number 1731) runs over inside the Concept2 Indoor Rower. There are four per machine. Sold individually. See more info.

    CHF 3,10
  • CHF 2,70

    For use on all Model C, D, E, and Dynamic Indoor Rowers and the SkiErg. Using this knob instead of a nut makes it easier to take the monitor on and off of the equipment.

    CHF 2,70
  • CHF 2,70

    For use on the Model C, D and E Indoor Rower. This is the end cap for the front of the indoor rower. See more info.

    CHF 2,70
  • CHF 2,70

    For use with Model C, D and E Indoor Rowers. These are the 1¼" diameter urethane pulleys that the chain runs over inside the indoor rower. There are two per machine: one is part of the traveling pulley (part number 1756); the other is mounted on a stationary axle and has two chain idler spacers (part number 1305) to keep it properly aligned. See more info.

    CHF 2,70
  • CHF 2,19

    For use on all Model B, C, D, E and Dynamic Indoor Rowers. This is the R8 bearing located outside of the flywheel. The corresponding bearing cup (part number 1013 or 258 depending on which model you have) is sold separately. See more info.

    CHF 2,19
  • CHF 2,19

    For use with Model A, B, C, D, E and Dynamic Indoor Rowers. This is the hard plastic cap that goes on the rear and/or front metal legs of the indoor rower to protect your carpet or floor and keep the machine from sliding back and forth while you row. Two to four per machine, depending on age and indoor rower model. Sold individually. See more info.

    CHF 2,19
  • CHF 1,60

    For use on the Model C, D and E Indoor Rower. This is the bumper for the rear of the monorail. See more info.

    CHF 1,60
  • CHF 1,41

    For use with Model C, D and E Indoor Rowers. This is the handle hook used on the Models C, D and E Indoor Rower. To store the handle long-term, place the handle up against the flywheel housing. For ease of use before or during a workout, placing the handle in the handle hook puts the handle within easy reach. Includes hardware.

    CHF 1,41
  • CHF 1,10

    This is part of the front monorail assembly. It is made of black plastic. For use on all Model C Indoor Rowers and on Model D Indoor Rowers manufactured from July 2003–2006.

    CHF 1,10
  • CHF 1,03

    This is the monitor bolt for the Model D and E Indoor Rower.

    CHF 1,03
  • CHF 0,95

    This is the bolt for the top seat roller for all Model C, D, E and Dynamic Indoor Rowers. Order two per machine. See more info.

    CHF 0,95
  • CHF 0,91

    For use with all Model D and Model E Indoor Rowers. This part is found inside the foot bellies. Order two per foot belly. See more info.

    CHF 0,91
  • CHF 0,91

    For use with Model C and D Indoor Rowers and all SkiErgs Plastic cover for the bearing on the left side of the Model C or D Indoor Rower, opposite the flywheel, and the back side of all SkiErgs.

    CHF 0,91
Showing 26 - 50 of 70 items